1970 Ford F250 Ranger XLT Camper Special 428 C6 Overdrive Fuel Injection Custom

Ford F-250 1970 Description

1970 Ford F250 Camper Special Ranger XLT 2WD

Clean title in my name.

California/Arizona truck until I drove it to Idaho a year ago.

7300 miles on it since drivetrain completion. Original mileage unknown.

Over $40,000 invested. $28,000 in parts (receipts included)

I have 100 photos of the truck, so let me know if there is something you want to see.

With Buy-it-now I will deliver to Portland, Eugene, Bend, or Orange County. Maybe a few other areas in the west. Contact me to discuss.

Engine:

428FE A-code block from a 1968 Galaxy cop car

Block was professionally machined and bored .060 over and deck milled .008

439 cubic inches, 11.5:1 compression ratio

ARP hardware throughout

Fully balanced

New Eagle Crank

New Eagle Rods

New Probe pistons with Total Seal rings

New Edelbrock Performer aluminum heads

New Edelbrock Performer RPM dual plane intake manifold

New Milodon gear drive timing set

New fabricated aluminum valve covers

New Lunati VooDoo cam

New Lunati hydraulic flat tappet lifters

New PRW shaft mount adjustable rockers

New MSD Pro Billet distributor

New MSD plug wires

New FiTech fuel injection

New Hedman thick flange headers with ceramic coating

New No Limit Engineering aluminum fuel tank mounted under the bed

New in tank fuel pump

New Fragola fuel lines with black anodized aluminum AN fittings.

New Russel black anodized aluminum fuel filter with serviceable stainless mesh screen.

New March serpentine pulley system (easily updated with A/C pump brackets)

New Pro-Amp single wire alternator

New Pro-Amp high torque starter

New Griffin radiator with electric fans

New Canton Racing high capacity oil pan

New Melling high volume oil pump

New motor mounts

New water pump

Drivetrain:

Rebuilt C6 auto transmission with shift kit and HD clutches

New Gear Vendors overdrive

New Hughes deep aluminum pan

New Hughes 2500 stall torque converter

New custom fabricated one piece drive shaft

New seals and bearings in the Dana 60 rear end

New Tru-Trac limited slip differential

New 4:10 gears with new shims, seals and Timken bearings

Rebuilt brakes, massive camper special discs up front, drums at the rear

New Hydroboost master cylinder

New power steering/brake pump

New Lokar transmission kick down cable and hardware

New transmission mount

Suspension:

Autofab lift kit with extended radius arms and camber corrected beams

New king pins

New ball joints

Rebuilt power steering box

New shocks

New Method 17x8.5 race wheels (custom drilled and center bored for this application)

New BFG TA KO2 34x10.5” tires (less than 1K miles)

Perfect alignment (will provide printout from the alignment shop)

Body:

1969 front clip

Shaved side markers and trim

New LED headlights

New Rigid Industries LED driving light flush mounted in the front bumper

New tail light buckets and lenses

New hood letters

New hood hinges

1967 hood side emblems (no plastic on the 67’s)

New bed side emblems

New rear bumper

New tail gate latch and hardware

New door handles

New lock cylinders

New door striker pins

New windshield and gasket

New sliding back window and gasket

New door seals

New side window seals/felts

Rhino Lining in the bed

Working bed cargo light

2” receiver hitch behind hinged license plate

Fuel filler is side mounted inside the bed so you can fill the tank with the tailgate closed and/or the bed fully loaded.

Factory bed side tool box with functioning lock and key

The only rust is the typical drivers side rear cab corner from water/fuel leaking in at the filler. Patch panels are readily available.

The cab fuel filler hole on the cab needs patched.

The hood came off another truck that had hood pins. The two holes need patched.

The doors need the mirror holes filled or some stock style mirrors installed.

Side window tint is pealing at edges. You can get new glass with laminated tint for a very reasonable price.

Wing vent windows work as they should, but the rubber seals are showing their age.

Interior:

New black cloth bench seat

New black carpet kit

New steering wheel and horn button

New turn signal switch components

New billet aluminum dash panel

New Isspro gauges (speed, fuel, oil pressure, coolant temp, voltage)

New FiTech digital gauge panel on the steering column, easily removed. Can be configured to show a single item like RPM, or multiple items (AFR, coolant temp, intake air temp, TPS, AFR trim, voltage, fan status etc. etc.)

New dash pad

New headliner

New sun visors

New seatbelts

New pedal pads

New arm rests

New door handles

New window cranks

New ignition lock cylinder

New billet lock knobs

New cigarette lighter

Original style radio works, but does not hold a signal well

Wipers work on all speeds

No windshield squirters (the reservoir, pump and wiring are not present)

Heater fan works on all speeds

New heater temperature control valve

Heater vent flap sticks and requires you to reach under the dash and help the flap. I just leave it in defrost mode because you still get warm air on your feet anyway. I was going to replace all this with an air conditioning kit eventually.

Dash light dimmer works

Interior dome/floor lights work

Ashtray opens as it should

Glove box opens and closes as it should

Kick panel vents work great

Between the wing windows, kick panel vents and rear slider, you get excellent warm weather ventilation that is not loud or buffeting.

New floor mounted high beam switch

New floor mounted overdrive switch

Rubber floor mats

Summary:

Nearly every moving part on this truck has been replaced or rebuilt. All the heavy lifting has been done. The engine, drivetrain, steering, brakes and suspension are all rebuilt and upgraded. The fuel injection has crisp throttle response and maximizes fuel mileage. You get all the classic look and feel, but with some added modern functionality. Cruises down the highway with the overdrive. Fly in and drive it home. Have some fun!