1967 Chevrolet Nova SS True Factory SS Documented Car

Chevrolet Nova 1967 Description

Documented 1967 Chevy Nova Factory SS Car No Expense Sparred 500 + HP - Well Detailed Pro Touring Beauty!
Highlights:
406 cubic inch V8 with electronic fuel injection Stock 400 C12 bolt block
4L801E 4-speed automatic transmission
Customized interior
Upgraded suspension
Rack-and-pinion steering
13" C6 corvette brakes
Sale includes complete build sheet docs, eceipts and information
American Torque Thrust 'M' Racing Chrome Wheels
DTS 12-bolt rear axle with Richmond 4:11 gear

Detailed Specifications:
Documented Factory SS New Mexico Desert Car, 17 SS VIN. Protect-O-Plate, otally disassembled, edia blasted and primed with zinc chromateprimer. PPG two part primer an PPG Concepts single stage Black Urethane paint. The body was fully disassembled and painted in pieces, henreassembled and wheeled.
The Rear of The Caris tastefully mini-tubbed with 14" between the steel so to the untrained eye it appears stock, ven inside the trunk. The rear frame rails are moved inboard,fully boxed and hand built from 12 gauge steel. The boxed full frame runs all the way to the sub-frame mounts at the firewall and is tied to the seat frame supports. The rear axle is a new DTS 12 bolt with Richmond 4:11 gear. Torsion center section, 3 spline Mosher axles with large Ford style bearings that are drilled for Chevy,Ford and Mopar wheels. Powder coated Mosher differential cover. Rear brakes are stock 12" C6 Corvette brakes. Finishing out with a 4 link set-up, ear sway bar, arge pan hard rod and QA1 12 way adjustable aluminum coil over shocks. Rear is built to handle in excess of 700 HP.
The Front of the carhas a TCI Mustang II Chassis shimmed square to the body with 6-way adjustable coil over shocks, ast ratio T-Bird power rack and pinion steering, 3" C6 Corvette brakes, tock rebuilt collapsible steering column, nd anti-vibration collapsible Borgenson steering shaft.
The Engineis an internally balanced 406 CI small block Chevy with electronic fuel injection that easily makes in excess of 500 HP and 500 ft/lbs. of Torque. The block is one of the few stock parts and is a 400CI 12 bolt block, which is stronger and 15 pounds heavier than a 400, bolt block). Torque plate bored + .030 and diamond plateau honed, ain bolts tapped for more thread engagement and studded, ine bored and decked. Wisco 11 to 1light weight forged pistons, ight weight tapered pins,barrel shaped molly rings, " polished and shot peened Scat rods, ightweight 4340 crank ground to .001 under to straight it, 28 oil pump, indage tray, quart Milodon pan and pickup, rodix Track One 23 degree CNC cylinder heads portered to the larger 1206 Felpro intake gaskets and flow 290 CFM at .005 lift-capable of making 600+ HP. Ferrea severe duty +.1.00 2.08-1.60 valves and 2.25" long manganese bronze valve guides, S1 valve seals, rane Solid Street Rocker Cam Sr-244/362-S2-12IG. Crane solid lifters, ual 1.55" springs and retainers Custom length push rods, orted Edlebrock Victor E intake, 000 CFM Edlebrock throttle body, 0# Bosch injectors, tainless steel fuel rails, 0 PSI return style fuel system with 10 micro in line filter.Steel braided fuel lines, dlebrock 3500 fuel injection computer, FI approved balancer, loyes true roller chain set-up, op quality Felpro gaskets and seals, RP head bolts, ain bolts, il pan studs and rocker studs. Comp 1.6 intake and 1.52 exhaust rollers, omp stud girdle.
The Transmission and Driveshaftwere designed to handle in excess of 700 HP. Transmission is a 4L80E built by Joel's on Joy in South Lyon, ichigan. It has as follows. 2.48 1st, .48 2nd,1.00 3rd and a .075 4th gear ratios. The front and rear gear assemblies are shimmed to .005 end play and the oiling system was modified for betterlubrication, eavy duty clutches, eavy duty bands and new shiftsolenoids. A high dollar Coan 3000 rpm stall converter with lock up, n elecronic sgift controller and a B&M Quicksilver shifter. The driveshaft is a custom steel 3 1/2 in diameter with solid 1350 series U-joint with a front drive shaft safety loopwelded between the seat mounting supports. This stiffens the floor of the car and protects the driver.
The Exhaust Systemis a handmade full 3" dual mandrill bent with x-pipe design with 4 mufflers. Best of both worlds here. Notable head turning sound when you put your foot in it...but you can take it on a road trip and not go nuts from the noise. It begins with S & S 1 3/4" ceramic coated headers that have 3" collectors, ollowed by a Dr Gas 3" X-pipe into a pair of 3? DynoMax UltraFlow mufflers. Continuing over the axle a pair of 3? DynoMax RaceBullets which act as resonators. There is also a set of 3" header flanges at the front of the rear axle either the front half of the exhaust system or the tail pipes can easily be removed for service.
The Interioris stock Super Sport Black with White Stripes. Stock Chevelle headrest were added which really fit perfect. Seats and tracks were stripped to bare metal, edia blasted, rimed and painted. All new foam inner material was installed before the new PUI Covers. All new SS side panels, mblems, eadliner, andles and remanufactured seat belt assemblies were used. Space age foam sound deadening material was used in the floor, irewall and roof to keep heat and noise out. New carpet, utometer Sport Competition Custom Gauge Set-up, en II Camaro SS Steering wheel and 68 Camaro Chromed disk brake pedals were used.
Air Conditioning Systemmade by Vintage Air with stock appearing A/C outlets. To make it fit neatly the battery was moved to the trunk. Blows ice cold and the engine still runs cool with the air on.
Tires and WheelsAmerican Torque Thrust "M" Racing wheels in chrome. 17x18 fronts with 17x10.5 rear Tires are 235-17-50 in front and 315-17-35 rear and are New "V" rated Radials.
Other quality componentsA 105 amp alternator that makes 50 amps at idle, pgraded bright headlights, ew steel cowl induction hood, pen top air cleaner, arge battery, gauge battery cables, igh torque big block starter, rethane engine and transmission mounts and bullet proof exhaust system hangers. All new tinted glass, ew window fuzzies, ll factory stainless steel trim polished, ew wheel well molding, ew bumpers, ail lights, eadlight bezels and grill assembly. Door hinges were rebuilt and new exterior door handles installed. New custom Aluminum radiator, EM GM 2-speed electric fan, quiet) and a Haden fan controller. Painless 12 volt circuit wiring harness.
Please note: The ONLY blemish I can find is a scratch on the left rear lower quarter were the owneraccidentally hit it with is wheel chair.
You could NOT build this car for twice as much $$. If you have always wanted one of the finest builds on a Pro-Touring car...this is your opportunity.
Terms: Cash or wire transfer ONLY. $500.00 non-refundable deposit within 24 hrs of the close of the auction. Balance due within 72 hours of auction close. No I do not need help selling this vehicle. Clear title. Please serious bidders only. If you win the bid,you have bought the car. You areencouragedto sendprofessional inspectors or inspect it yourself prior to bidding.All information and specifications were provided to me by the widow of the owner. No warranty implied. Please note my 100% feedback. I have tried to describe this car to the best of my ability. I can also assist with helping you locate car transport.
Again...the price we are asking is extremely fair. It would cost much, uch more for this build. Serious bidders may contact Jim with questions at 816-729-8513